DIY Modern House Number Plaque

• Craft Time:  1 hour
• Waiting Time:  2 hours
• Skill Level:  Intermediate
• Cost:  ~$30 (depends on how many numbers there are in your house number)

• 1/4” birch plywood
• Wood shims
• 5″ floating mount house numbers
• 1×2 common board
• Wood stain
• Paint

• Sanding sponge
• Wood glue
• Rag
• Mallet
• Drill
• 5/32 drill bit
• Measuring Tape
• Saw
• Micropinner 

First, cut your base plywood that you will glue the wood shims to. Mine was about 15″x26″. This will get trimmed down later, so it can be a rough cut.

Place your wood shims one by one next to each other with the fat edge of the shim flush with the edge of your base plywood.

Some wood shims come a little more beat up than others so pick and choose until you have them placed the way you want. As you can see below, the bottom shim would need more work to look smooth, so if you have enough shims just set that one aside and grab a different one.

Working a few shims at a time, pick up your shims and use wood glue on the plywood to attach the shims to the board. Continue until they are all glued down.

Once the glue has dried, run your wood shim board through the table saw to make the sides even. If you don’t have a table saw, you could also use a circular saw, band saw, or jigsaw.

Sand all your edges and the top of your shims now to smooth everything out. I’m obsessed with  sanding sponges  and they really help get all the edges.

Clean off your shim board to make sure there isn’t any sawdust and then stain your board with a rag. I stained mine with some leftover  golden oak stain  I had from our  entry bench .

Alright, now time to add your numbers. I got these 5″ floating mount numbers off Amazon and they look great. They are made to just go directly into your exterior, but they work great for this project too.

Twist the mounts onto the back of the numbers and use a measuring tape to center your numbers. Once you get them placed, put some pressure on them to mark where you will need to drill. Since we’re working with soft wood shims, it should be fairly easy to see where the holes go as you can see below.

I found a 5/32 drill bit worked best for the house numbers. With a scrap board underneath the plywood, drill all your holes and then use a mallet to softly pound the number mounts evenly into the board.

I love how they appear floating and will be easier to see from the road.

Next up, the frame.

Since the floating mount numbers are designed to go into the exterior of your home, there is about an inch sticking out the back of the sign that we need to hide.

Take your 1×2 common board and cut your wood at 45-degree angles using a miter saw or miter box to fit perfectly around the shim board.

Sand all the edges as needed once they are cut to size and fit around the board perfectly.

I gave my frame pieces two coats of matte black spray paint. This is my hands down  favorite matte black spray paint,  but if you can’t find that one  this one  is a great second option.

Now, it’s time to attach the frame. Start with the long sides. Add wood glue to the long edges and then set your shim board on a flat surface. The goal is to have your frame as far back on the board to hide the screws that are sticking out the back.

Set the side boards and then pin them on the edges and middle with a  micropinner  to hold it until the glue dries.

Once the long edges are pinned, you can add the end pieces with a little more glue and a pin in each corner.

If you’re a messy worker like I am and get wood glue all over, just give your frame a quick sand and touch up paint and you’re done.

Now, you just need to hang your house number sign. I would suggest attaching a picture hanging wire to the back of your frame and then a screw into the exterior of your house. Just be sure to silicon where the screw is to make it waterproof.